STUFF
|
09-28-2005, 08:11 AM
|
Owner
 
Posts: 5
Threads: 4
Joined: Nov 2026
Reputation:
0
|
Member No. 1 · 3007 posts · joined 4-May 03 · Chosen One
Ok, so all of a sudden I have a bunch of computers not working right and I need to fix them.
My brain can not work properly right now, so I need some help lol.
First I'll tell you about my most important computer. Mine.
My computer has been having issues for a while. Which I believed was the fans. And in a way it was. Because I had this bad fan that was vibrating WAY too much.
So I replaced the fan in it with the fan of a 1.2 Ghz CPU I used to have. My computer is a 2.6GHZ so I knew this wasn't going to be good, but for now it was going to have to do.
My video cards fan had broken a while ago, and I actually had that 1.2Ghz CPU fan on my video card. So that means that now my video card had no fan.
Now, my computer was acting better, much better, but still not right and my Video card was getting rather hot every day.
I kept having problems like audio not sounding right. Not all audio though, just certain audio. It would like slow down.
Same with video. I have this one video that I was editing and it would play very slow. Kinda very broken up too. Hard to explain.
Anyway, I finally got my new fans yesterday, I installed them, and for some weird reason, when I turned on the computer, it wouldn't turn on at all. No anything. No sign of electricity in there at all.
After getting really frustrated with it, I left it alone for a few hours.
Well, hours later I come back and I push power and it starts.
But now, while booting, it does the RAM check as normal, but then, right before checking the IDE drives, it stops. It doesn't do anything. In order to get it to continue, I have to push the power button twice. The first time I push it it seems to get the hard drive moving, and the second time it actually checks for the drives and continues.
The first few times I had my mouse hooked up to my KVM switch and I got to the loging screen, but whenever I'd move my mouse, the computer would go into sleep mode. or Hybernation. Don't really know the difference.
So I took out the mouse from KVM switch and put it in the USB port on the back of the computer.
Well, I get into Windows just fine, and the sounds and videos are still playing wrong.
Well, what happens now? My computer keeps going into hybernation, or sleep, or whatever after so many minutes. I don't know if it's always the same ammount of minutes or not.
All my power management options are set to Never, so it shouldn't do that. I never used to.
So, that just about sums it up for that problem.
Now on to 2.
Problem 2
There is this church I do the network for. All computers were working fine. It's 5 computers and 4 of them are connected to a DI 524 router and one is wireless.
Everything has been working fine, but yesterday they called me because the internet wasn't working.
So I go to check the computers. Right away I restart the Modem and the Router.
The Wireless computer works fine. However the others aren't.
When I go to my DOS prompt and type "ipconfig /all" I notice that instead of a "192.168.0.100" kind of IP, they have IPs like regular computers have when connected to the net without a router.
However, the internet is still not working in them.
When I try to connect to the router thru one of them by going to "192.168.0.1" they dont' connect, but the wireless one does.
I hooked one of them straight to the modem, and it still didn't work.
This BTW is a DSL line. And I don't have the Yahoo DSL software installed in it so thats probably why it didn't work when hooked straight to the modem.
The modem IS working because the wireless one does get internet.
So I'm thinking either the Router is bad, or something is not allowing these computers to get their IP from the Router.
Any help with any of these problems will be greatly apreciated. Also if you guys need more detail on anything, let me know and I'll see what I can do.
thnx
|
|
|
|
|
| White Knight |
09-28-2005, 09:22 AM
|
Unregistered
|
Member No. 14 · 3296 posts · joined 7-June 03 · Super Moderator
I have a router related problem also. I have a PC and a laptop both theoretically working thru the router. Cuz... well if I unplug the router, all network goes haywire.
Anways both computers connect through to the internet but are unable to form a workgroup between themselves. No matter what I do they just don't recocnise each other.
minus the spelling errors
hihiii
STUFF - I doubt it is much use, but out of curiosity, could you tell us the temperature inside the PC case on problem 1.
|
|
|
|
|
STUFF
|
09-28-2005, 09:40 AM
|
Owner
 
Posts: 5
Threads: 4
Joined: Nov 2026
Reputation:
0
|
Member No. 1 · 3007 posts · joined 4-May 03 · Chosen One
You know, I could have sworn that in the BIOS there was something to tell me the temperatures, but I can't find it 
|
|
|
|
|
| White Knight |
09-28-2005, 11:20 AM
|
Unregistered
|
Member No. 14 · 3296 posts · joined 7-June 03 · Super Moderator
There are alot of 3rd party apps for it, but crazy should know more than me. I can't even shut down my computer =\
AFAIK, I'd suggest doing a fresh network install on prob#2. I found that always the easiest, cuz I can't be bothered to check into further detail.
This post has been edited by White Knight: Sep 28 2005, 11:24 AM
|
|
|
|
|
| Tibs |
09-28-2005, 01:34 PM
|
Unregistered
|
Member No. 342 · 95 posts · joined 2-September 05 · Members
anarchy(stuff), check the matrix forums as I posted my reply to your issue there.
|
|
|
|
|
| Tibs |
09-28-2005, 01:47 PM
|
Unregistered
|
Member No. 342 · 95 posts · joined 2-September 05 · Members
here's a copy and paste of what I put in the matrixls forums: ^_^
.......................................................................
Ok on your personal pc, heat is very bad... very very bad (though I'm sure you knew that ). I have a feeling that your processor sustained a small amount of heat related damage, thus why you are having weird and unpredictable issues. Video card GPU's seem to be a little more tolerance of heat and usually you'll have a capacitor bust on a video card before the GPU takes any damage (key word 'usually'), so most likely your video card should still be fine.
I would try and find another CPU that your motherboard supports (even if just a loaner) to try it out. If everything comes up fine after that then you have found your culpret. If you get everything running but you get artifacts or anomalies in any 3D intesive app, then you might find a video overclocking app for the GPU chipset you have and underclock it some (as most of these utilities will allow for underclocking as well). I have found that doing this can make flakie video cards work satisfactory.
You might also manually underclock your CPU via either the bios or your motherboard (depending on what you have) and see if that helps any as well. I would personally lower the FSB and not the multiplier (that way your not having to try more variations of underclocking than neccessary)
................
ok, on the network setup... my 1st question is, are the pc's that can't connect to the internet pulling an IP address of 169.254.xxx.xxx with a subnet mask of 255.255.0.0? If so, then that means these pc's cannot connect to a DNS. When windows cannot communicate to a DNS it resets the IP and subnet mask so it can at least talk with any other pc's connected to the same network (that also cannot connect to a DNS). Also, get on 1 problem pc and try to ping another problem pc, that way you can verify if the router is even remotely doing it's job.
On the router itself, check the various settings including port forwarding... cause if it's forwarding port 80 to the wireless pc then only that pc will be able to surf the web. Also, most routers have a hard reset that resets everything back to factory defaults. This usually entails putting the end of a paperclip in a hole, powering it off, powering it back on and then removing the paper clip from the hole... this of course various from router to router.
Hope this helps, if you have any other info to provide that you think may be usefull then feel free to post it.
~Tibs
|
|
|
|
|
STUFF
|
09-28-2005, 07:59 PM
|
Owner
 
Posts: 5
Threads: 4
Joined: Nov 2026
Reputation:
0
|
Member No. 1 · 3007 posts · joined 4-May 03 · Chosen One
Hey Tibs, Thanks a lot
I'm not totally sure what I did, but the boot up process isn't stopping anymore.
I think some of the other problems have to do with that windows partition, because I have 2 windows partitions and everything is working fine on this other one.
|
|
|
|
|
STUFF
|
10-06-2005, 07:33 AM
|
Owner
 
Posts: 5
Threads: 4
Joined: Nov 2026
Reputation:
0
|
Member No. 1 · 3007 posts · joined 4-May 03 · Chosen One
Here is an update with the problems I'm having here:
The problems with my computer are pretty much solved.
As for the Church network I'm working on. It's confusing the crap out of me.
I thought maybe the Router was bad, so I tried a new router. New Router didn't work either.
I still had 3 computers that didn't connect to the net, and 1 that did. The wireless one.
So I tried hooking up the wireless computer to the network with a cable to see if that part of the router was working. And it works fine. I was able to connect to the router and the internet using that computer.
I decided to try hooking up that cable (the one on the computer that was now working) to one of the computers that wasn't working.
On one of them, I see lights flashing in the router for that connection but it still wouldn't get a local IP from the router and it still wouldn't connect to the internet.
I can't even ping 192.168.0.1 which is the Address for the router.
So I tried the cable in another computer. On this one, I don't even get lights blinking in the router. So it's not doing jack.
Now, thru all this I've reset the router 100 times. . . or 5.
I've also restarted each computer after trying something new.
Nothing.
So I decide to try this winsockfix.exe. Which is supposed to fix windows sockets. I run it, but nothing.
So I'm like, maybe it's spyware or a virus. So I run ad-aware and AVG and nothing.
So I decide, maybe it's still a virus and my definitions were too old. So I decided to do the one thing I hate doing. Format, re-install.
So I reinstalled windows on this one computer. The install process went smooth.
However, it still didn't work!!!
So I've put in a new router, and I've reinstalled windows, and it still doesn't work. And I'm going to go crazy if I don't find out what the hek is wrong with this piece of shit
|
|
|
|
|
| crazybeans128 |
10-06-2005, 04:15 PM
|
Unregistered
|
Member No. 174 · 1998 posts · joined 22-January 04 · Council Member
What operating system is it? Also, you may want te enable NetBIOS of TCP/IP. I once had a problem we thought was the router and turned out to be something else. You can find it by going to the Properties of the network hardware >Internet Protocol > General : Advanced > WINS: Enable NetBIOS over TCP/IP. Check that setting, and just go through with those. Also make sure the IP's are automatic. That's all I can really think of, and although I don't think I'm the network guru here, I had problems like this I had to solve at my own house. So yeah... good luck on that.
|
|
|
|
|
Tynvar
|
10-06-2005, 05:21 PM
|
Junior Member
 
Posts: 2
Threads: 0
Joined: Nov 2026
Reputation:
0
|
Member No. 98 · 496 posts · joined 29-July 03 · Council Member
That Netbios thing only works for me with win98 or me machines. But then they cant see winxp or win2000 ones very well. I would stay away from that. Why dont you take your router to each machine directly so it gives it a new ip and see if its the computers or cables.
|
|
|
|
|
|